|
|
11038
|
(4) NEW 5" Swivel Casters
|
(4) NEW 5" Swivel Casters - -Installs into a 7/8" Hole - 3-1/2" from center of wheel to top of swivel plate. Wheels are Rubber on Polypropylene hub - Swivel and wheel are ball bearings - Weight 10#
|
$30.00
|
For
4
|
|
|
11080
|
(2)
NEW Swivel Casters
|
Pair of NEW Faultless Bearing Swivel Casters # 29993 - 5" Rubber Wheel 1" Wide 90 Durometer - 2-1/2" x 3-1/2" Swivel Plate - 2-7/8" x 1-3/4" Bolt Pattern - Wheel Says #22 - E-5 -- 6" Total Height - Weighs 5# for the pair
|
$20.00
|
For
2
|
|
|
12253 |
(2) NEW 2 inch Tandem
Swivel Casters |
(2) NEW Tandem Ball Bearing Swivel Casters - Wheel measures 2" OD x 7/8" Wide each - 2-3/4" Overall Ht. - Approx 200# Cap Each - 3/8" -16 Threaded Stud. Weighs 2#
|
$8.00
|
Both
|
|
|
14362 |
(4) NEW Solid Rubber Tires - Traction Thread |
(4) NEW Solid Rubber Tires - Traction Thread - Size is 4.00-4 # MP901 - Matador - Made in Slovakia - Center ID is 4" and narrows down to 3-1/2" in middle. All 4 Weigh 70# and will ship in 2 35# Boxes. |
$10.00 |
For all 4 |
|
 |
21574 |
(4) NEW
6" Hard Rubber Wheels |
(4) NEW
6" Hard Rubber Wheels - .660" ID - 2.150" Length Thru Bore - Rubber
wheel measures 2" Wide and is crowned in the middle for low resistance
and high speed. Aluminum Hub - Bearing on each side of wheel is 6203-RSV
- These sell for about $30.00 each |
$30.00 |
For All
4 |
 |
26426 |
(2) NEW Albion Cast Iron
Spoke Wheels 5X2 |
(2) NEW Albion Cast Iron
Spoke Wheels 5X2 - 5" OD - 2" Wide - 1/2" Bore or 3/4" Bore if you
remove Steel Bushing - Roller Bearing Design - Weighs 12# |
$28.00 |
For
Both |
 |
27400 |
(20)
NEW Bassick 2-1/4" Lockable Casters |
(20)
NEW Bassick 2-1/4" Lockable Casters - Dual Wheels Overall 1-5/8" Wide -
3/8" Threaded Stem - Weighs 8# |
$35.00 |
|
|
|
|
|
|
|
|
|
|
11015
|
72" x 12" Wide Gravity Conveyor
|
72" x 12" Wide Gravity Conveyor made by Span-Track by Unex - Contains (24) 3/4" x 11" Rollers which spin very easily because of nylon bushing on each end of roller. Rollers are made of Aluminum and are spaced at 3" apart from each other. Roller is slightly higher that the rail so you can put a container wider than the 12" width. Capacity is about 50 Lbs. per foot. Rail is Galvanized Metal and measure 2-1/8" Tall. This unit weighs 20 Lbs. and can be taken apart to save shipping.
|
$25.00
|
|
|
|
12391 |
NEW 10 ft
Rex Table Top Chain # LF1843TK1.25 |
NEW Rex
Table Top Chain # LF1843TK1.25 - 1-1/4" Wide 10 foot long comes with
connecting link. Weighs 10#
|
$30.00
|
|
 |
19267 |
Honeywell Powered Roller
Interface Module |
Honeywell Powered Roller Interface Module - # SDS-C1PRD-4 - No Cables or Connectors are included - |
$100.00 |
|
|
 |
21601 |
(6)
2.5" x 6" Precision Rubber Rolls |
(6)
American Roller Company Part # MSRACXXFEABVA01 - 2.5" OD x 6" Long
Precision Rubber Rolls - Each side has been machined to 1.570" bore for
Ball Bearing - Label says these are made for Minster Press Weighs 20# |
$45.00 |
For All |
|
|
|
|
|
|
|
|
 |
20353 |
NEW 36 VDC Contactor N.O Contacts |
NEW 36 VDC Contactor N.O Contacts - Coil # C-7214 -
Base measures 4-1/8" x 3-1/4" - 4-1/2" in Height - Contact Silver tips
are about 3/4" OD - Weighs 5# |
$145.00 |
|
 |
20596 |
(ONE)
NEW 36 VDC Intrupa Contactor |
NEW 36 VDC Intrupa Contactor -
Contactor Manufacturing Company - Number on Coil is C-7308 - Base Measures
4" x 3-1/4" - 5" Tall - One Normally Open - One Normally
Closed Contacts - Silver Contacts measure about 5/16" Round - Picture
Shows two to show both sides but the price is for only one |
$100.00 |
EACH |
 |
20599 |
NEW 72-80 VDC Intrupa Contactor |
NEW 72-80 VDC Intrupa Contactor
- Contactor Manufacturing Company - Number on Coil is C-7212 - Base
Measures 4" x 3-1/4" - 4-1/2" Tall - When Energized ALL
Points are Common - Silver Contacts measure about 5/8" Round - Weighs
7# |
$80.00 |
|
| |
20599 |
NEW 72-80 VDC Intrupa Contactor |
NEW 72-80 VDC Intrupa Contactor
- Contactor Manufacturing Company - Number on Coil is C-7212 - Base
Measures 4" x 3-1/4" - 4-1/2" Tall - When Energized ALL
Points are Common - Silver Contacts measure about 5/8" Round - Weighs
7# |
$80.00 |
|
|
VB1 |
94232-OOR-OS |
CROWN
Vehicle Circuit Board (Qty of 2) |
$85.00 |
each |
| |
VB2 |
94509-01 |
CROWN
Vehicle Circuit Board (Qty 3) |
$85.00 |
each |
| |
VB3 |
116150-OOS |
CROWN
Vehicle Circuit Board (Qty 4) |
$85.00 |
each |
| |
VB4 |
103849-OOR |
CROWN
Vehicle Circuit Board (Qty 3) |
$85.00 |
each |
| |
VB5 |
103804-OOR |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
| |
VB6 |
116150 |
CROWN
Vehicle Circuit Board (Qty 3) |
$85.00 |
each |
| |
VB7 |
094299-OOS- |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
| |
VB8 |
118610-OOS- |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
| |
VB9 |
94366 |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
| |
VB10 |
102831 |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
| |
VB11 |
94495 |
CROWN
Vehicle Circuit Board (Qty 4) |
$85.00 |
each |
| |
VB12 |
94378 |
CROWN
Vehicle Circuit Board |
$85.00 |
each |
|
|
20862
|
NEW GE 36
VDC Contactor 200 Amps
|
NEW GE #
120D212X51 - 36 VDC Contactor 200 Amps - Coil # 1D154G32A - Contact Arm
activates a Limit Switch # CR115B2 when energized - Base MEasures
5-1/2" x 2-3/4" - Shows some nicks in base but minimal - Weighs
7#
|
$150.00
|
|
|
|
20864
|
NEW 36
VDC Contactor 200 Amps
|
NEW
CT171A36 Contactor - Coil # C-2332 - Contact Arm activates a Limit Switch
# 9007AO2 when energized - Base Measures 5-1/2" x 2-3/4" -
Weighs 7#
|
$150.00
|
|
|
|
20868
|
NEW VDC
Intrupa Contactor
|
NEW Slightly Damaged - VDC Intrupa Contactor - Was Tagged with # GEIC4482CTRA700AH208X0 Description # DTR-BAKE5266 - Contactor Manufacturing Company - Number on Coil is C-7208 - Base Measures 4" x 3-1/4" - 4-1/2" Tall - One Normally Open Contact - Screw in coil has a small nick should not effect operation See Picture - Weighs 7#
|
$85.00
|
|
|
|
20875
|
NEW VDC
Intrupa Contactor
|
NEW VDC
Intrupa Contactor - Contactor Manufacturing Company - Number on Coil is
C-7312 - Base Measures 4" x 3-1/4" - 5" Tall - One Normally
Open - One Normally Closed Contacts - Silver Contacts measure about
5/8" Round - Weighs 7#
|
$80.00
|
|
|
|
20903
|
(2) NEW
Trupar Solenoids
|
(2) NEW
Trupar Solenoids - # MFD2AF11450AA - Desc# DTR-FRDS4505 Relay - Weighs 3#
|
$25.00
|
For
Both
|
|
 |
21027 |
IC3645EV Vehicle Control Card |
General Electric - IC3645EV Vehicle Control Card - GE#
EV100PH1P2A - This unit says Genuine GE Re-manufactured - came out of a
maintenance inventory cabinet at an industrial auction. Weighs 3#
|
$360.00 |
|
 |
21087 |
36 VDC Raymond Forklift Main
Pump Motor |
36 VDC
Raymond Forklift Pump Motor - 570-432 - Measures 6-1/2" OD 9-1/2" Long
- Shaft is .590" with a 1/4" Slot recessed in about 1/2" - This unit
weighs 50# |
$320.00 |
|
|
 |
21064 |
NEW
Gleason Hydraulic Dual Reel |
NEW
Gleason R35-LH15 Dual Line Hydraulic Dual Reel - 2,000 PSI - Measures
15" OD - 1-1/4" between flange plates - Outside plate has small ding on
it but is in excellent condition otherwise - Weighs 40# |
$180.00 |
|
 |
22225 |
NEW 24 DC Volt Contactor |
NEW 24 DC Volt Contactor
made by Contact Industries - Part# CT600A24D1S -- 22TS03-25 - Footprint
is 4" x 2-1/4" - 5-1/4" Tall - Top Contact Plate measures 2" x 6-1/4"
and has (2) 3/8" Holes on each side for Lug mounting - comes with surge
protector acros |
$45.00 |
|
 |
27532 |
NEW GE Rectifier Module #
44A727011 |
NEW GE Modules Cat#
171B3939G4 - For Electric Vehicles - Cat# on module in bag was #
44A727011-G05 - is 259A0220PXC - Weighs 2# |
$65.00 |
|
 |
28005 |
General Electric Fanuc EV-1
SCR Module IC36450SC |
General Electric Fanuc EV-1 Module # IC3645OSC1H3 - Has Remanufactured
Tag on it appears to be NEW - Good for 24-48 VDC - Does not have
Terminal Connector |
$280.00 |
|
| |
|
|
|
|
|
|
|
3980
|
(2) New Hubbell Crane Control Inserts
|
These are two brand new Hubbell Crane Pendant Pushbutton inserts Part No. 64605-001. These are primarily used on DC cranes. both are brand new in box.
|
$65.00
|
|
|
|
10836
|
2 Sets of 8" Crane Brake Shoes
|
2 Sets of 8" Brake Shoes - There is a Number C2674 which may help identify it. Shoe measures 4" Wide Friction Material -- 4-1/4" Wide (Outside Dimension @ Pin Hole -- 3-1/4" Inside @ Pin Hole -- 5/8" Pin Hole -- Please Note that one of the shoes has a braze repair, the other 3 are in perfect shape.
|
$ 35.00
|
|
|
|
11211
|
Insul8 Dual Spring Loaded Collector Arm for Crane |
Dual Spring Loaded Collector Arm for Crane - Made by Insul 8 - 30 Amp per Arm - Red Collector Housing is Part # M-839 - Mounts on 1" Square Bar - Weighs
|
$40.00
|
|
|
|
11260 |
(2) Large Crane Collector Arms |
(2) Large Crane Collector Arms - Spring Loaded parallel links measure about 20" Long - Bakelite Insulating piece measures 9" long x 4" Tall - 2-1/4" wide - Note there is no copper rail connector on these - I believe these are made by insul8 - Weighs 20#
|
$45.00 |
|
|
|
13088
|
NEW Size 7 Bullard Golden Gate Hook 4.2 Ton
|
NEW Crosby Bullard Golden Gate Hook 4.2 Ton - Stock # 1051453 - Locking Latch cannot release until release lever is pushed - 3/8" Alloy Chain connects into top block - Swivel Hook - Weighs 15#
|
$75.00
|
|
|
|
13536
|
75' of 1/4" Acco G-30 Proof Chain
|
75' of 1/4" Acco # 4001-20416 -- G-30 Proof Chain - 1250# Lifting Capacity - Measures 1/2" x 1" on inside - Weighs 50# -
|
$50.00
|
|
|
|
13861
|
8 Conductor Crane Collector Arm Assembly
|
8 Conductor (1 Ground) Crane Collector Arm Assembly -
Manufacturer is unknown - 8 Arms measure 4-3/4" Across & 3-3/4" Long from pivot point - Collector is 1-3/4" Long 1/8" Thick - Approx 36" Wire leads coming from Arm - Comes with spare assembly Rack with Brass inserts - Weighs 2#
|
$18.00
|
|
|
|
15330 |
Daniel Woodhead 2 Speed - 6 Button Pendant Control # 4026-2 |
Daniel Woodhead - 6 Button Pendant Control # 4026-2 - Two Speed - For Indoor Use but Does have Gasket to seal from Dust and Oil - Measures Approx 13" - Weighs 5# |
$100.00 |
|
|
|
18576
|
(4) Crane Festoon Flat Wire Track Hanger
|
(4) Crane Festoon Flat Wire Track Hanger - Used in C Rail Track - These are used but seem to be in pretty good shape may need some cleaning and suggest oiling the wheels - several available - weighs 5 # for the 4 pieces -
|
$15.00
|
For all 4
|
|
|
18578
|
Crane Festoon Flat Wire Track Hanger
|
Crane Festoon Flat Wire Track Fixed Hanger - Used in C Rail Track - used but seem to be in pretty good shape may need some cleaning - several available - weighs 1#
|
$5.00
|
|
 |
28318 |
NEW - McKissick 1 Ton Hook
Block with Safety Latch |
NEW - McKissick 1 Ton Hook
Block with Safety Latch - HK Bullard - Style 2D - Automatic Pin Gate
Part # 1050606 - Weighs 5# |
$45.00 |
|
|
|
|
|
|
|
|
|
|
7494
|
1/2" Double Hoist Block
|
Picked this one up at a recent auction. Looks like it handles 1/2" Rope. It appears it was made by Monarch Hoist. Not to sure what the capacity is but it has a #34 on
it
|
$20.00
|
|
|
|
11922
|
Aero-Motive Tool Balance BF 18
|
Aero-Motive Tool Balance # BF 18 - Adjustable for 13-18 Lbs. - Tested works Very Good - Weighs 10# |
$50.00 |
|
|
|
12108
|
100 ft of Campbell #45 Sash Chain
|
100 ft of Campbell #45 Sash Chain # 0894524 - BLU-Chrome Finish -- 175 Ld Load Limit (79Kg) - Weighs 12#
|
$18.00
|
|
|
|
13251 |
NEW Box Campbell Chain or Attachment ID Tags |
NEW Box Campbell Chain or Attachment ID Tags Item # 7503506 -- ID Tag has Stamped on one side - SIZE - GRADE - SERIAL# - Opposite Side REACH - WLL - 60^-90^ - You stamp in the information of chain or attachment - Lifting chains are required to have ID Tags - 50 Pcs. per Box - Weighs |
$35.00 |
|
|
|
19000
|
30 Ton
Coil Grabber
|
30 Ton
Coil Grabber - I Believe the is made by Cullen-Friestedt - Measures about
120" Long Has not yet been test or inspected but appears to be in
good working Order - Call For More info 440-236-4007 - FOB Cleveland OH |
$8000.00
|
|
|
|
|
|
|
|
|
